Protective Coating

Protective Coatings: Industrial coating – Sydney

CCMP provides the application of a full range of architectural, industrial and marine coatings to your metal product/structure strictly in accordance with specifications, standards, government specifications and data sheets. We have an extensive range of application equipment, filtered paint areas, and an experienced application team.

We provide steel coatings that can range from epoxy primer systems and single coat zinc which can be applied by hand or complex airless systems for high-density industrial products and conventional spray guns.

Our product application range includes but is not limited to:
  • Etch primers and single pack
  • High build zinc phosphate/zinc phosphate primers

  • Organic zinc rich primers

  • Zinc silicates – inorganic, water borne

  • Epoxy primers

  • High Build and Ultra High Build Epoxy

  • Polyurethanes

  • Polysiloxane

  • Polyaspartic coatings

  • Fluropolymer

  • Alkyd enamels

  • MIO coatings (Micaceous Iron Oxide)

  • Protective coatings resistant to heat (for commercial ovens and exhaust refineries etc.)
  • Protective coatings for the marine industry (a triple coat system is good for  coastal environments)
  • High-density triple coat epoxy systems for use in chemical plants etc.

  • Non-Slip, wear & abrasion resistant coatings

  • Intumescent Coatings

Need a Quote?

Send us your requirements
& we will send you a quote.


Our workshop less than 45 Minutes from Sydney & Newcastle metro areas

  • We can transport your material to our facility
  • Our factory is over 3500m2 (2 Workshops)
  • Overhead crane capacity to 20 Tonnes. (Heavy lifts over 20 Tonnes are managed by use of load mobile crane companies
  • Significant lay down area for coating application indoors within both workshops
  • Fleet of forklifts up to 10 Tonne capacity service the yard area
  • YARD: Fully concreted area (over 4000 M²) for storage of incoming/outgoing goods and to minimise dust
  • Fleet of forklifts up to 10 Tonne capacity service the yard area
  • CCMP’s experienced site applicators are also able to carry out protective coatings out in the field and on your project

Need a Quote?

Send us your requirements
& we will send you a quote.

It is critical to specify the right industrial metal coatings including the abrasive blasting/sandblasting process. We provide industrial metal coatings for domestic, industrial, commercial and architectural needs in Sydney, Newcastle, and throughout NSW. Industrial metal coating is important for:

  • Rust control/Effective corrosion
  • Creating desired aestetic appearance
  • Creating an extended lifespan for your steel product or structure

Abrasive blasting/sandblasting in NSW is a necessary process for both new and used steel structures and products because without it, paint or any protective coating will not adhere to the surface properly. Even new steel has a residual coating following the manufacturing process that needs to be removed before it can be painted. Our abrasive blasting is available to our clients in Sydney and Newcastle, (and wider NSW) and is also a standard procedure that takes place before steel is galvanised.

At CCMP, we use a variety of abrasive mediums in our blasting process, depending on the quality and age of the steel involved and the specifications you supply us. Blasting agents include steel grit, glass bead, copper slag and garnet.

Our Abrasive blasting in NSW and the subsequent application of protective metal coating to steel structures, products and parts:

  • Increases longevity
  • Rejuvenates (renews old structures, making them look as new)
  • Can be re-done unlimited times for added durability, strength and cost savings.

Got a question? We welcome your enquiries, call now.

Why choose CCMP?

We are a large, well-equipped total corrosion control service provider on the east coast of Australia. We have the facilities and equipment to:

  • Collect your steel structure or product in one of our fleet of trucks and prime movers,
  • Prepare the surfaces for abrasive blasting, industrial spray painting , protective metal coating and abrasive blasting/sandblasting processes in Sydney, Newcastle and wider NSW in-house and in accordance with your specifications, and
  • Service any project (industrial or domestic), no matter how big, small or complex.

Once we have carried out sandblasting in Sydney or wider NSW, the exposed ‘raw’ steel is highly subject to immediate rust, even in transit. The benefit of having the abrasive blasting and protective metal coating completed at the one site is therefore obvious. As general rule of thumb, protective coating must be applied to steel within 4 hours of blasting.